Protegra OF 3000 - Reverse Osmosis, 3000 l/h

The picture may be different from the article and can include supply, which is not in the standard scope.

 

The Protegra OF 3000 reverse osmosis system

The Protegra OF 3000 cost-effectively produces larger quantities of deionized water. Equipped with high-quality components and an intelligent control system, the system must be connected to a tank with level monitoring to control production. The system provides high purity water with the advantage of continuous operation. Production runs automatically in two operating modes.

Product features and benefits:
- With energetically economical and high performance reverse osmosis membranes, a high output of pure water is achieved with a high salt retention rate at the same time. This minimizes the energy requirements and reduces water loss.
- Before each standby an automatic system flush is performed to reduce the ion concentration at the membranes which increases the life and reliability of the system.
- A microprocessor controller monitors the pure water quality and the status of the system. Exceeded values, such as expired maintenance intervals and water quality are displayed as alarm messages.
- The limit values for conductivity and flow rate of the pure water can be set individually.
- The system is structured clearly and can be operated from all sides for service purposes.
- The system is low-maintenance.

Pure water production: Reverse Osmosis
- Feed water solenoid valve
- Pressure regulator
- Conductivity sensor for feed water (cell constant c=1.0)
- filter housing includes four  20" filter cartridges, 5 µm
- Pressure switch for feed water
- Stainless steel pump (1.4401/1.4301)
- Pressure sensor for operating pressure
- 3 Reverse osmosis modules 8" from polyamide/polysulfone with GFK cylinders and end caps
- Regulator for concentrate flow to drain and return flow
- Three flow sensors for pure water and concentrate
- Conductivity sensor for permeate (cell constant c=0.2)
- Quality dependent permeate distribution valve

Microprocessor Control:
- Located on the front of the system
- System status
- Conductivity of feed water and permeate
- Volumetric flow of pure water and concentrate
- Reminder service and filter change
- Alarm indicator for: low flow feed water, out of range conductivity, flow rates and tank volume
- Tank level indication in Percent, three options for unit to switch ON or OFF. Pump protection against running dry for pure water
- Connection for common alarm to BMS with adjustable time interval (optional single alarm possible)
- Time schedule for concentrate to drain and module rinsing
- Multilingual (German, English)
- RS232 interface, with optional software for further data processing

Delivered with:
- Operating manual
- Electrical diagram
- CE certificate

Connection possibilities:
- Potential free contact for common alarm
- Booster pump start/stop function with dry-run protection and interval operation
- Feed water hardness monitor. In the event of hardness breaking through the unit switches off to prevent blockage of the RO membranes

Optional:
- Reminder for service intervals (potential free contact)
- UV-disinfection kit with interval operation
- Timer switch for use in connection with pressure booster pump

Feed water specifications:
Flow rate: 4000 - 6000 l/h
Pressure: 2 - 6 bar
Conductivity: < 2000 µS/cm
TDS: 1000 mg/l
CO2: < 20 mg/l
Total Iron: < 0.1 mg/l
Free Chlorine: < 0.1 mg/l
Temperature: 5 - 30°C
Softened or hardness stabilized

Performance specifications:
Delivery flow rate at 15°C: 3000 l/h
Salt retention: 98 %
Recovery rate up to: 75 %
TOC: < 30 ppb
Bacteria reduction: > 99 %

Technical data:
Operating pressure: max. 14 bar
Mains input: 3 x 400 V, 50 Hz
Power consumption: 5.5 kW/h
Ambient temperature: 5 - 35°C
Fuse: 16 A

Feed water connection:
R 1-1/2" male BSP
Permeate water connection:
R 1-1/2" male BSP
RO permeate, drain connection:
R 1-1/2" male BSP
Pure water back-pressure: 1 bar

Dimensions and Weight:
Height: 1900 mm
Width: 3900 mm
Depth: 960 mm
Weight: 345 kg

Please note:
The unit accepts a feed water salt content of 1000 mg/l, equivalent a conductivity of 2000 µS/cm at 15°C.
The feed water specifications are guidelines.