Protegra CS PRO RO EDI 750 - Reverse Osmosis with Ionpure EDI, 750 l/h

The picture may be different from the article and can include supply, which is not in the standard scope.

 

Protegra CS PRO RO EDI 750
Reverse Osmosis with Ionpure EDI, 750 l/h

CONSISTENTLY HIGH WATER QUALITY

The Protegra CS® Pro RO EDI system is a high-performance purification solution for deionised water applications. Featuring industry-leading reverse osmosis technology and a high-performance Ionpure® CEDI cell, the system maintains water quality at the required standard.
The system is ideal for a range of laboratory and industrial applications with a typical water quality of > 0,07µS/cm and flow rates up to 750 l/h at 15°C.

Product features and benefits:
- Energy efficient and high performance reverse osmosis (RO) modules effectively achieve high inorganic retention and permeate production. This reduces energy demand and  minimizes water waste.
- Electro-deionization removes the residual salt content from the water without exhausting itself.
- Automatic rinsing of entire system before going into stand-by mode reduces build-up of ions in the RO membranes - increasing the lifespan.
- Microprocessor control provides automatic operation with continuous monitoring of all important parameters.
- The limits for conductivity and flow rates of pure water can be set individually.
- Removable front and side panels for easy service access
- The system is low maintenance.

Production of pure water: Reverse osmosis
- Feed water solenoid valve
- Pressure regulator
- Conductivity sensor for feed water (cell constant C=0,1)
- 10" 5µm foamed polypropylene depth filter
- Pressure switch for feed water
- Stainless steel pump (1.4401/1.4301)
- Pressure sensor for operating pressure
- 4 Reverse osmosis modules made of polyamide/polysulfone with pressure tubes made of stainless steel (1.4571) and end caps made of polypropylene (PP)
- Regulator for concentrate flow to drain and return
- Three flow sensors for pure water, concentrate and brine
- Conductivity sensor for permeate (cell constant C=0,2)
- Quality-dependent permeate distribution valve

Continuous Electrodeionization (CEDI):
- Ionpure CEDI module for up to 750 l/h
- Conductivity sensor for pure water, temperature compensated (cell constant C=0,1)
- Temperature sensor

New 7" touch-panel control:
- Mounted on the front of the system
- System status displayed
- Conductivity of feed water, permeate and pure water
- Volume flow rate of pure water, concentrate and brine
- Alarm indicator
- Timeline for concentrate discharge to drain and module rinsing
- Multilingual (German, English)
- USB interface for data transfer
- microSD-Port (Data recording and firmware updates)

Supplied with:
- Operating manual
- Electrical circuit diagram
- Fine filter cartridge 5µm Big Blue
- key for filter cartridge
- Power cable NOT included

Optional:
- Water guard 1" (W2T808003)
- LED-Signal light tower (Red-yellow-green) (W3T307039)
- Communication interface (Modbus gateway) for continuous data transfer to a BMS (Building management system) or PC/ laptop (W3T570885)
- Membrane degassing (W3T262426)
- Complete DQ/IQ/OQ/PQ documentation and validation of the system on site available upon request.

Feed water specifications:
Softened or hardness stabilized

Flow rate: 1100 - 1500 l/h
Pressure: 2,5 - 6,0 bar
Temperature: 5 - 30°C
Conductivity: < 1400 µS/cm
Colloid index (SDI): < 3
TDS: 700 mg/l
CO2: < 10 mg/l
SiO2: < 10 mg/l
TOC: < 1500ppb
pH: 3-9
Total iron: < 0,1 mg/l
Free chlorine: < 0,1 mg/l
Manganese: <0,05 mg/l

Performance specifications:
Flow rate at 15 °C: 750 l/h
Conductivity: < 0,1 µS/ml
Typical conductivity: < 0,07 µS/cm
Recovery rate up to: 50-80%

Technical data:
Mains input: 400V 3/N/PE 50/60 Hz
Power consumption: 3,0 kW/h
Ambient temperature: 1 - 30°C
Humidity: no condensation
Fuse protection: max. 16 A
Residual current device (RCD formerly FI):
Type B, 30mA, short-time delayed
Sound pressure level: max. 64db(a)

The power connection is made via supply terminals inside the Protegra and must be provided by the customer.

Hydraulic ports:
Feed water: G1.25" MPT, d25 SOC
Product water: G1" MPT, d20 SOC
Concentrate: G1" MPT, d20 SOC
Brine: G3/4" MPT

Dimensions and weight:
Height: approx. 1795 mm (fixed stand)
Height w/ optional lamp: 1960 mm
Width: 650 mm
Depth: 665 mm
Weight: approx. 275 kg

Please note:
The unit accepts a feed water salt concentration of 700 mg/l, equivalent to a conductivity of 1400 µS/cm at 15°C.
The feed water specifications are guidelines. The pure water specifications can only be guaranteed if a feed water analysis including levels of silicate and CO2 of the installation
site and all other relevant parameters have been analyzed.